In this video I go over the basic gunsmithing tools that every DIY Gunsmith Should Have. Make sure to visit my Amazon storefront for a list of the tools I cover here. https://amzn.to/3qxG0FF Take care of your guns with the right tools! Whether you are building, repairing or upgrading a gun, Having the right tools will help make your firearm work safer and professional looking. 0:00 Introduction 0:15 Safety First! 1:10 The Right Screwdrivers 2:06 Allen Hex Wrenches 3:36 Punch Sets 4:01Jewelers Hammers 4:31 Needle Nose Pliers 4:45 Pad or Carpeting 5:48 Calipers 6:44 Vise Blocks and Pads 8:06 Sight Tools 9:24 Torque Screwdriver or Wrench 10:14 Crows Foot Wrenches 11:01 Bore Sighting Tool 11:45 Vise and Vise Pads #GunsmithTools #FirearmTools

In this video I go over the features of the Sig Sauer Romeo 5 red dot sight and give a view of an actual sight picture Here's is an affiliate link to one if you are interested in one, Sig Sauer Romeo 5 Sight https://amzn.to/3BTh1bl Romeo 5 XDR and Juliet 5x Micro Combo https://amzn.to/4jfVz11 #SigSauer #Magnifier #Romeo5

Cannon sent me an NL lock and keypad replacement for this Cannon Gun Safe . It wasn't a direct replacement for the original Lagard and it didn't fit quite right! Follow along and see how I replaced the entire lockset and keypad and fixed the problem the new lock presented. This is a follow up to the first cannon safe video I posted where the keypad failed. I was able to recover that by replacing the keypad. Here I replace the entire lock mechanism. Check out our DIY Website https://extremediy.org 0:00 Introduction 0:40 Disclaimer 1:01 Tools You Will Need 1:28 Removing the Panel 1:50 Locking Bolts from Inside of Safe 2:06 Different Locks 2:14 Removing Old Lock 3:29 Removing Old Keypad 3:40 Installing New Keypad 5:00 Installing New Lock 7:52 Uh Oh! Relocker Bolt Problem 9:37 Fixing the Relocker Bolt issue 9:48 Explanation of the Gun Safe Relocker 11:25 Second Disclaimer! 11:45 Final Lock Installation 12:52 Final Test & Success! #gunsafe #replacelock #electroniclock

How to easily open a cheap home safe when you have lost your combination, have dead batteries or no key. I took a break from my usual videos and decided to do this one, it's short and was fun to do. Probably something everyone with a cheap home safe should know! If anything else, it proves just how bad these safes are at protecting your valuables! Check out my Amazon Affiliate Review Videos (I may earn commissions on these videos): https://www.amazon.com/shop/josesextremediy 00:00 Introduction 00:34 The Hack to Open the Safe 01:11 The Inside, Why it's easy to open 01:46 Slow Motion of Safe Failure 02:18 Putting it Back Together 02:38 Second Demonstration and Wrapup #HomeSafe #NoCombination #NoKey

I found a good way to fix my Cannon Digital Gun safe fail. The digital keypad died and I was locked out. Fresh batteries didn't help, it was dead. But I found a way to fix it without drilling the safe! I called Cannon and they agreed to send me a new lock. They also told me I would have to get the safe drilled. I called a local safe expert who quoted me $400-$800 to drill the safe. I would rather buy a new safe! So, I did some research and found out how to fix this without drilling the gun safe! They told me, "Don't drill, try this first" and it worked! ***Note - This is not a video on how to break into a Safe, it assumes the safe is yours and you know the old combination*** Check out my Amazon Affiliate Review Videos (I may earn commissions on these videos): https://www.amazon.com/shop/josesextremediy This helps support our channel as we earn commissions from sales. Here's is a paid link to the dehumidifier I mentioned in the video: https://amzn.to/3s9qDaC Here is a link to a LaGard 5715SC Panel. This is the same company that gave me the technical advice on how the digital locks work and the solution I used. https://mbausa.com/1-battery-keypad-satin-chrome/ Here is a link to the written version of this video: https://bit.ly/3pFuLLJ Check out our DIY Website https://extremediy.org Contents: 0:00 Introduction 0:35 How the Safe Keypad Failed 0:55 800 Dollars to Drill the Safe! 1:30 How to Remove the Old Keypad 3:05 Explanation of Lock Cable 4:46 New Keypad Arrived! 6:55 Testing the New Keypad 8:41 Mounting the New Keypad 12:15 Why You Shouldn't Drill a Safe #GunSafe #GunSafeFailure #FixGunSafe

How to Protect your safe from unauthorized Access! As the dust settles from the recent Liberty safe fiasco, I thought this would be timely. Basically I go over how to secure your safe from an unauthorized access through the manufacturer accidentally giving out a default factory combination and thereby compromising your safe. By the way, this applies to any safe manufacturer. In all fairness to Liberty Safe, they released the combination after seeing proof of a warrant. They have also announced that a customer can have the history of their safe expunged or removed from their records. Below are paid affiliate links to two replacement lock bodies and combo pads that I would use. S&G and LaGard are standards in the industry. I would definitely avoid any no name cheaper brands. La Gard https://amzn.to/3sQA8Ok S&G https://amzn.to/486kvT1 DISCLAIMER: This video is not intended to defeat or circumvent law enforcement! If they have a warrant then they will get in your safe! The video simply describes a process in which you can swap out the factory lock body which in effect, removes the old factory code. If you have an older safe, this is probably something you want to do anyway. The lock body on my safe failed a few years ago and I was very lucky that I was able to get in with a replacement combination pad so I could replace the lock body. This video goes over the complete process.