MrHowToDo

How to field strip a Shadow Systems MR920. Always check that your firearm is clear. This is even more important for Shadow Systems firearms since the trigger needs to be pulled to disassemble the firearm.

How to field strip a Glock 17 Gen 3 The steps to disassemble and reassemble apply to other models and generations. Always check that your firearm is clear. This is even more important for Glocks since the trigger needs to be pulled to disassemble the firearm.

How to adjust retention on a Bravo Concealment polymer magazine pouch Different magazines fit differently so you may need to adjust the retention of your magazine pouch. This video shows how to adjust retention on. Bravo Concealment magazine pouch, but it may apply to other polymer magazine pouches. The video uses a Glock 17 magazine and a Canik TP9 SFX magazine.

How to use a very budget friendly battery tester to check your battery’s power The budget battery tester is an older version of one found on Amazon to check how much juice is left in a battery. This video shows a couple different types of batteries - double A, 9-volt, CR2032, and CR123A. The tester used does not have a protruding bottom piece so a steel paper clip is used as a conductor.

How to attach a suppressor to a Taurus TX22 This video shows how to remove the barrel collar, attach the threaded barrel adapter and then screw on a Dead Air Mask 22 HD. And also shows a short clip comparing unsuppressed vs suppressed.

How to change the combination on a Brinks 3 digit lock Pushing in the button can be done with a pen but if you already have another lock, you can use the end of the other lock to press the button in

How to install a BX-Trigger on a Ruger 10/22 Takedown This also quickly shows disassembly and reassembly of a Ruger 10/22 Takedown

How to fix a stuck slide on a Canik SFx Rival S. This may apply to other Canik models. If the user attempts to reassemble the slide back onto the frame from the front, it will get stuck since parts get in the way. The slide is meant to be reconnected to the slide from past the middle area of the frame.

How to field strip a Canik SFx Rival S. This video shows how to disassemble and reassemble a Canik Rival-S for cleaning. The grip is a brass Lok Grip and is not the original grip.

How to field strip a Canik SFx Rival S. This video shows how to disassemble and reassemble a Canik Rival-S for cleaning. The grip is a brass Lok Grip and is not the original grip.

How to install a Magpul Cheek Riser on your Magpul X-22 Stock for a Ruger 10/22. This video shows removal of the standard cheek riser and the installation of the 0.5” cheek riser to raise the cheek rest to a comfortable level for a red dot. The size of the cheek riser depends on your face and the height of the sight or optic.

How to adjust the retention for tier 1 holsters (Centurion shown in the video). This applies to other holster brands that use a similar setup with rubber spacers.

How to disassemble and reassemble a 380 M&P Shield EZ Magazine.

How to use a Maglula AR15 / M4 loader / unloader

How to attach a molle pouch. This video uses a molle strap with a snap fastener, but the same weaving applies to other types.

How to replace batteries on a Howard Leight Impact Sport earmuff and then make it easier to replace in the future.

How to reassemble a Dead Air Mask 22 HD suppressor. Only tool needed is the front cap tool.

How to remove and re-attach a Magpul SL stock with just an allen wrench. Before working with any firearm, make sure the firearm is cleared.

How to use a portal digital tire inflator that uses a 12v dc plug. I am not sponsored by the product and I do not work for them. But if anyone is interested, the specific one shown is a cheap FBK brand from Amazon. There are other brands there that work similar. This specific one also has attachments to inflate bike tires, balls, and other stuff.

How to disassemble a Dead Air Mask 22 HD suppressor. Only tool needed is the front cap tool. If there is too much carbon on the baffles, a light tap by your finger or plastic rod can loosen it.

How to save your hearing while shooting a Glock 17 using the SilencerCo Omega 36m.

This video will show how to configure some of the accessories for the Omega 36m quickly and easily. This includes going from the original long configuration setup with ASR mount, changing it to a short configuration, swapping out the front cap, switching to a piston mount and switching to a 3-lug mount. The items shown are: Omega 36m (comes with ASR mount and tapered insert) Charlie Flash Hider Front Cap Charlie Piston Mount (comes with piston for 1/2x28 9mm, spring, spring retainer, piston housing, coupler ring) 3-lug Mount (9mm) Tools used are the ones Omega 36m comes with: Charlie Spanner Tool Charlie Multi Tool It does not cover direct thread, fixed barrel spacer, or showing how to install the adapters onto the firearms (which is basically done by screwing it on...).

This video shows how to install a Volquartsen Recoil Assembly (Rod and Recoil Spring) for a Ruger Mark IV 22lr pistol.

This video shows how to replace the extractor from a Ruger Mark IV 22lr pistol. I will be replacing it with a Volquartsen Exact Edge Extractor.

How to use the Maglula pistol magazine loader to load and unload a magazine. The pistol loader fits 9mm to 45 ACP The video uses an H&K VP9SK magazine and 9mm Snap Caps