DTC P2626 air fuel ratio sensor replacement Hyundai Elantra √ Fix it Angel

11 years ago
30

Repair Manuals: https://shrsl.com/3zwnv https://sovrn.co/amfaf3n Fix it Angel EBAY STORE: https://ebay.us/OE6UsK repair smith https://fxo.co/1284793/fixitangel THANK YOU ALL FOR WATCHING MY VIDEO. This video is NOT sponsored. If you would like to support this channel. These links are my affiliate links which means if you buy something I will receive a small commission. Thank you for your support. God Bless
https://www.amazon.com/shop/fixitangel https://www.getsomevegas.com/home
2006 2007 2008 2009 2010 Hyundai Elantra.

Air fuel ratio sensor https://amzn.to/2E9tt5D
https://tinyurl.com/y4zcjrdc
GearWrench Metric Flex Head Wrench Set
https://amzn.to/2HFpq4p
http://tiny.cc/w37e4y
oxygen sensor wrench https://goo.gl/j53fKP
https://goo.gl/CFdCL3
oxygen sensor socket https://amzn.to/2YiqO1N
http://tiny.cc/3uzd4y
3/8 Drive FlexHead Ratchet https://goo.gl/QVMstw
https://goo.gl/jjDK9r
3/8 Drive Metric Socket Set https://goo.gl/sRTnaT
https://goo.gl/MyyyWU
3/8 dr. Metric Deep Socket Set https://goo.gl/6KCiYG
https://goo.gl/DxQBJM
3/8" Drive Extension Set https://goo.gl/HrOvhn
https://goo.gl/hpyyHw

2006 Hyundai Elantra. DIY Replaced the air fuel ratio sensor, It is actually called a Air Fuel Ratio Sensor.
Problem: Diagnostic Trouble Code (DTC) P2626, Linear heated oxygen sensor Bank 1 Sensor 1 (HO2S11) pumping current circuit open / Probable cause 1. open or short circuit condition 2. poor electrical connection 3. failed HO2S11 ( Bank 1 Sensor 1)
Solution: First visually check sensor wires for any cuts or chaffing. Check if connector is fully seated in. Check if any oils in the connector. Test sensor heater circuit for a short or open.

DTC P0030 HO2S HEATER CONTROL CIRCUIT(BANK 1 / SENSOR 1)
The PCM determines if a front HO2S heater fault has occurred and sets DTC P0030 if the front HO2S heater control driver inside the PCM fails, if HO2S is not operational (after an elapse of predetermined time) since engine start, or when the front HO2S tip temperature is out of normal working range.

The information contained in this video is for general guidance, not responsible for any errors or injuries that you have done.. please subscribe and thank you for watching. Follow me on TWITTER: @88bmyvegas. Used my Samsung W200 camcorder to do this video. DISCLAIMER - Due to factors beyond the control of FixitAngel, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. FixitAngel assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. FixitAngel recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of FixitAngel, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not FixitAngel nor any of it’s subsidiaries. All links in the description are affiliate links. if you would like to support this channel. purchase any of the product links. i get a little commission from each purchase. thank you

Loading comments...